Spark plug insulators are made of a ceramic Drbrabrhrart, pressure resistant and high voltage insul

Candle engine with 25,000 volts of high-voltage electric pulses repeatedly into the combustion chamber Dhd.alktrvdhay durable transmission of electric current between those who can throw a mixture of air and fuel arc or spark to the engine combustion forecasting and preparation. Under intense pressure and heat are ready to spark their millions of times. With the increased power output of the motor-vehicle pile in the car, the harder and more intense.
Each candle has a metal part. The hexagonal shape of the metal to the pile to be installed securely into place.
The bottom of the threaded portion of the cylinder head wrapped in a negative electrode of the bottom portion is removed, a refractory linings, which is threaded on the outside edge that is located in front of the candle in the washer on the cylinder copper with a combination of copper and asbestos U-shaped in cross section (U) has to be prevented from leaking out of gas in the combustion chamber, at the location of some of the piles, and Uribe as well as sealing. More Shmhay today screw diameter of 14 mm. Although some candles with 18 mm diameter how to unshrink clothes and some Qtrshan10 mm. Usually thread pitch 2/1 or 5/1 mm are the specifications screw pile foundation is 25/1 times the bolt diameter Kmtrbray Qtvrtraz 14 for two-stroke engines and motorcycles made candles when Shvd.payh Baydba combustion chamber cylinder heads were shorter how to unshrink clothes Bashd.chnanchh level selection can cause scaling and if the protruding hot longer itineraries in both the case of self-immolation.
Spark plug insulators are made of a ceramic Drbrabrhrart, pressure resistant and high voltage insulation. This placed so that the oyster shell exterior and interior with a fire-resistant gasket sealing compound how to unshrink clothes is totally separate.
The addition of insulation that keeps Rang h Alktrvdmrkzy as a protector for electrical current to the electrode as well as the electrode just Bgzrd.ayq to high heat, cooling and vibration resistant upper part of the insulation that is exposed to dust should always be kept clean to prevent how to unshrink clothes wasting electricity. In some types of piles, there are occasional stack insulation can be gathered through the stack Gsafthay away.
Plug has two intermediate electrode (positive) and side (negative) that are attached to the body. The middle electrode is placed in the center of ceramic insulation against high pressures how to unshrink clothes up to 40 atmospheres and temperatures up to 2000 C resistant. Side electrode is attached how to unshrink clothes to the metal shell and the central electrode spark gap that spans the distance called. Span between two electrode spark plugs, ignition is the first factor. This distance shall be the engine characteristics, if the distance between the two electrodes is too low, weak spark and cause engine how to unshrink clothes malfunction and is not clear.
If two Alktrvdkhyly is high, the motor will run till the period of good times in the course of or having to squeeze coil turns that light is not idle or bad. The electrodes should be placed in the front part of the quadrilateral how to unshrink clothes are parallel and form, by mutation of the spark plug opening is done easier.
New two-piece candles and candle central electrode wire is attached to the upper and lower part of the combustion chamber continues. Some 1000 ohm resistor is placed. These parasites are resistant radio and television, and also increases the life of the candle. Electro sex of refractory metal such as iron and chromium alloys, nickel or alloy that is a good conductor of electricity how to unshrink clothes and heat resistance is high.
Piles or electrode conductor is bipartite. One electrode to the other wire to the body of the distributor how to unshrink clothes cap, spark plug and the other end of each of the electrodes at a little distance from each other, how to unshrink clothes causing a wave of high voltage circuit inductance, the electric current to the coil inside the distributor cap, and from there the wire that plugs into one of the electrodes.
Then the flow of the gap between the electrode and the electrode to the other end of the pile bounce and body, and is thus the gap distance between the electrodes of the spark jumps electric current, the circuit is completed and the flow of electricity to will be showed.
Complete how to unshrink clothes the electrical circuit is one of the most important secondary winding, another important fact is that when electrical current to the spark plug electrode gap distance between two passes, how to unshrink clothes the last thing a spark and the circuit, do ignition how to unshrink clothes .
In general, how to unshrink clothes two types of candles, hot and cold are divided. Hot candle is designed to keep the temperature sufficiently in Cape ceramic how to unshrink clothes and carbon burn oil deposits in the heating mode, the insulator nose programs.
Cold type is designed to prevent premature ignition. The heat, the faster it flows, so that these types of candles how to unshrink clothes at a time when the engine must withstand high loads, be used. In warm, due to the higher, the nose of the combustion gases are exposed to cold and cold in comparison with the candle, how to unshrink clothes the temperature is higher.
But in the heat, the engine is the most important operational candles (candles recommended to be designed in various thermal range). Due consideration is that the temperature range of temperatures above the piles must act to prevent the scaling or dirt